screenshot-www.thingiverse.com-2022.04.12-19_13_55-e30b2765

Folded lamp shade v2

One more lamp shade, this time a little more intricate and with rounded corners for easier printing. Printed in a semi-transparent silver.

Instructions

See http://www.thingiverse.com/thing:110736

Edit: Added a v2 model with a straight profile at the bottom, which works better with Slic3r's spiral vase mode.


screenshot-www.thingiverse.com-2022.04.12-19_03_49-fcb11c92

Spiral Planter

Inspired by the Spiral Vase (https://www.thingiverse.com/thing:481259) and taking design cues from the Globe Desk Planter Flower Pot (https://www.thingiverse.com/thing:2834004) I have designed this spiral planter with integrated water dish.

Turns out pretty well using Formfutura's Stonefil material.

I have printed at 0.1mm and 0.2mm layer height with 100% infill.

Print Settings

Printer:

Wombot Skeletus

Rafts:

No

Supports:

No

Resolution:

0.1 - 0.2

Infill:

100%

Filament brand:

Formfutura

Filament color:

Concrete & Granite

Filament material:

Stonefil


screenshot-www.thingiverse.com-2022.04.12-16_05_04-2a2134c7

Paper Plate Storage Container

This paper plate holder will hold about 100 paper plates up to 8.5in wide. The slot inside of the container allows for easy grip of the top layer plate.

Print Settings

Printer brand:

Printer:

Rafts:

No

Supports:

No

Resolution:

0.2mm

Infill:

20%

Filament brand:

OVERTURE

Filament color:

Digital Blue

Filament material:

PLA+


screenshot-www.thingiverse.com-2022.04.12-15_41_04-46e8631a

Light Switch Lock

4/21/16
For citizen named "lowlight". Added a slight modification to the design. This will make it harder for the switch to accidently be turned off by adding support against the switch arm.

I have a problem with people turning off light switches that for most part need to stay in the on position. If you have a boiler switch or front door light that you like to keep on, this device will help remind your busy fingered friends that this switch is not to be touched. Although the design allows you to over-ride the on position by moving the arm out of the way and still turn off the switch.

You need to print with support there is a detail the has a cut away to clear the switch area.

I also included the CREO .pk2


screenshot-www.thingiverse.com-2022.04.11-18_33_19-e5690614

Garbage Bag Dispenser Side Wall Hang

This is a customization of an original model by JAYTEEAU. His design worked great but I didnt have a area to screw this part flat. So I made a closed end so it can be hung on the right wall. I print this at 200mm/s on my ender 3 with 10% infill. Takes about 19 hours. I use 1 1/4 inch wood screws. I was concerned about the screw head grabbing the bags. with 3 a 3 layer wall you can squish the PLA so the wood screw will be flush to the inside of the cylinder and not grab the bags. I have linked JAYTEEAU's orginal file below. Happy printing.

https://www.thingiverse.com/thing:2757789

Print Settings

Printer brand:

Printer:

Ender 3 Pro

Rafts:

No

Supports:

Yes

Resolution:

0.2

Infill:

10

Filament brand:

Filament color:

Black

Filament material:

PLA


screenshot-www.thingiverse.com-2022.04.10-23_30_43-66439a7c

Shell Separator Bowl

I present a simple solution to be able to eat nuts and place the husks in an appropriate place.

Many times when we eat nuts we usually throw them in a container whose function is not that (in my case Cups, Glasses)

With this bowl you have 2 in 1, container for the fruits, and container for the peels.

Follow me for more.


screenshot-www.thingiverse.com-2022.04.10-22_38_46-b0d4cd60

Tiny Secret Book

I started out just wanting a book model that I could print out in two colors so that the pages could be white (or gold for a Bible:) and it turned into this. Why settle for a simple book, when the book could hide something inside?

The pages slide out of the cover and slide back in with a nice snap to keep it closed. You gently pull the cover back a little to disengage the tab.

At it's default size, you can stack two SD cards inside one book. It also works well for stashing a few Tylenol or emergency candy. (SPREE!)

Tiny Bookcase is now also available to store the books.

Updated 03.01.2018: I replaced the BookPages.stl after discovering a very tiny error with the top not being perfectly level. The one available now should be good to go.

NOTES ON SCALING via Kittish
"Doesn't quite scale smoothly. Had to do some adjustments, at 2x scale the pages don't quite fit right. For the pages, I had to adjust x down one millimeter, y up one millimeter and z up by .5 millimeters for it to fit properly inside the cover without wiggling around too much or having gaps where there shouldn't be any."
See her make here: https://www.thingiverse.com/make:452750

Print Settings

Printer:

Monoprice Maker Select Ultimate

Rafts:

Yes

Supports:

No

Resolution:

0.2

Infill:

see notes

Notes:

tl:dr;
BookCover: Raft, 0% infill, no supports
BookPages: No raft, 25% infill, no supports

I had the best luck printing the book cover on a raft since the edge is fairly thin and can droop a little with the heat. I also set the infill of the cover to 0% with fine results.

The book pages block is simpler. No raft is needed, but the infill needs to be in the 20% to 30% range.


screenshot-www.thingiverse.com-2022.04.10-22_09_36-f03ba233

Rag Holder

Rag holder to screw to the wall.

No support required.

2 OPTIONS :

  • With hole to screw it to the wall, ~Ø3,5mm screw
  • Without hole to glue it down.

MY BLOG

Print Settings

Printer brand:

Printer:

Ender 3 Pro

Rafts:

No

Supports:

Yes

Resolution:

0.16

Infill:

25%

Filament brand:

IDK

Filament color:

Grey

Filament material:

PLA


screenshot-www.thingiverse.com-2022.04.10-22_03_04-132edbf8

Stackable Shoe Rack

Download link is broken and thingiverse is not fixing it. To download, go below the thumbnails there is the section "thing files". Click on that and download the STL there.

Hi Everyone, This is a shoe rack design based off of my Monitor stand. This can be printed on a Prusa Mk3 Bed dimensions. You will need to print with no top and bottom layers. The pictured infill is 5% honeycomb with 9 perimeter layers.

For the piece of wood. You can use any 3/4 thick wood, plywood,mdf, laminate etc. The depth is 8 inches and the length is however long you would like.

Print Settings

Printer brand:

Printer:

Rafts:

No

Supports:

No

Resolution:

.2

Infill:

5%

Filament brand:

prusament

Filament color:

Galaxy Black

Filament material:

PETG or PLA


screenshot-www.thingiverse.com-2022.04.10-21_33_00-e2344fea

OC lamp

Just like my previous work, I use 5050LED and need some glue to assemble.
5050LED
The length of the 5050 LED is 1m and ip20 no waterproof
(https://www.aliexpress.com/item/1857949964.html?spm=a2g0s.9042311.0.0.27424c4dOLuS0P)
https://www.amazon.com/gp/aw/d/B07XZ82QVW?psc=1&ref=ppx_pop_mob_b_asin_title

'LED cover.stl' is LED diffuser.

2020.12.14 Linked version has been added.
2021.01.28 mid_holder split right.stl mid_holder split left.stl ring holder.stl has been added

Print Settings

Printer brand:

Printer:

Ender 3 Pro

Rafts:

No

Supports:

Yes

Resolution:

0.2

Infill:

15%

Filament brand:

DYAIR

Filament color:

free

Filament material:

PLA