screenshot-www.thingiverse.com-2022.04.12-15_26_59-1ad47d6c

Chameleon Pen Holder (High-Res)

The idea is not new and there is already one remix available but I wanted more smooth surface and bigger plus centered hole for the pen.
(hole diameter : 10mm)

for bigger pens simple scale it up (example:12mm Hole scale up 120%)

prints fine without support

Thanks goes to Ishibashi-san (bs3) for the design
ありがとうご ざ います

please check here as well:
https://www.youtube.com/channel/UCkWGgSjbHl0JN86glKJZuTA

Print Settings

Printer brand:

Printer:

Rafts:

Doesn't Matter

Supports:

No

Resolution:

0.2mm

Infill:

20%

Notes:


screenshot-www.thingiverse.com-2022.03.28-13_18_33-73786e95

Spray-can holder

This is a chain style can holder, you can connect them as much as you need.
Move one side slightly up to make inclain that prevent the can from falling down (it works fine even if its level).

Print Settings

Printer brand:

RepRap

Printer:

Prusa I3

Rafts:

No

Supports:

No

Infill:

100

screenshot-www.thingiverse.com-2022.03.27-21_25_31-6ccde824

Battery Box AA + AAA

PLA+ 185 deg filament and 60 deg bed
30% fill on lid and base
100% fill on tubes and insert


screenshot-www.thingiverse.com-2022.03.16-11_39_00-1d42b7e7

Key Holder

Hi all,

Just a simple multilevel Hexagonal Key tidy.

There are 3 heights of key fob to match the varying heights of the holder. Below are the quantities of each you would need to print to fill the holder but I think it looks better if you leave some gaps

x4 - 15

x11 - 20

x4 - 25

Depending on your printer you may need to scale the print to fit on your bed.

Technically there should be a 0.1mm gap between the fob and the holder but I had a slight issue with the squish effecting the fit of the fobs into the holder so I scaled the fobs slightly more than the holder.

I scaled to;

Holder = 70%
Fobs = 68.5%

Just because I preferred the smaller fob size for the keyrings.

Update:

I have added a v2 holder to fit the 15mm key fobs. That way you can print all 15's.
I have also added a v2 with holes as i know someone mentioned mounting it on a wall.

Cheers

Print Settings

Printer:

Rafts:

No

Supports:

No

Resolution:

0.16

Infill:

25%

Filament brand:

Amazon Basics

Filament color:

Any

Filament material:

PLA


screenshot-www.thingiverse.com-2022.03.15-17_02_02-69777430

Cable Holder

A simple cable holder. Works with lightning and many other usb cables.

Print Settings

Supports:

Yes

Resolution:

0.1 mm

screenshot-www.thingiverse.com-2022.03.14-17_58_52-c74bde76

Shelf Holder Set

Shelf holders you can customize and 3D print.
I made three in scale 4 cm, 8 cm, 12 cm


screenshot-www.thingiverse.com-2022.03.14-12_32_35-e792b9c1

Toilet paper holder - 100% Printed

Not having found what met our expectations, I designed this support without screws.
The assembly is done by butterfly seal from the rear.

This is the 1st version and does not allow the parts to be reversed. Assembly and printing should be done following the picture showing the name of each part.


N'ayant pas trouvé ce qui correspondait à nos attentes, j'ai concu ce support sans vis.
L'assemblage se fait par joint papillon par l'arrière.

Ceci est la 1ere version et ne permet pas l'inversion des pièces. L'assemblage et les impressions doivent être faits en suivant l'image indiquant le nom de chaque pièce.

Print Settings

Printer brand:

Printer:

Rafts:

No

Supports:

No

Resolution:

.28

Infill:

15

Filament brand:

Giantarm / Sunlu

Filament color:

Wood / Black

Filament material:

PLA / PLA wood

Notes:

The butterfly joint was designed to fit not too tight. If the parts are not tight enough, it may be necessary to increase the scale a little.


Le joint papillon a été conçu pour s'adapter pas trop serré. Si les pièces ne sont pas assez serrées, il sera peut-être nécessaire d'augmenter un peu l'échelle.


screenshot-www.thingiverse.com-2022.03.13-22_02_09-ce0b8e94

Hot Glue Gun Stand - Narrow

Remixed (split model, overlapped halves and recombined in Fusion 360) to suit a small Bostik Hot Glue Gun which has 22mm wide body. Worked perfectly.

*** If you need a bigger stand, consider the original version - this is a remix

*** Thingiverse "Download All" Button / Link currently not working for many models across Thingiverse, including this one. Please just use the Download Button for the Single STL file

Print Settings

Printer brand:

Printer:

Rafts:

No

Supports:

Yes

Resolution:

.16

Infill:

50%

Filament brand:

Aurarum

Filament color:

Sky Blue

Filament material:

PLA

Notes:

I used Tree supports (Cura) at front edge of cradle part only ... wanted a nice clean edge


screenshot-www.thingiverse.com-2022.03.07-20_34_32-835b7ea4

SpecStand Vertical Desktop Eyeglass Holder

This is a handy desktop eyeglass or keyring stand with hook. the base has four internal cavities for pennies which can be added during the print for a weighted base if you add an M601 command to your gcode in order to pause the print before layer 2.6 starts.

The main stand body does not need supports, but the hook does require supports. I suggest printing 2 hooks at a time to allow cooling in between layers of this small part. Make sure you clean any support material from the hook's v-tabs and file down gently if necessary for easier assembly, if it's too tight of a fit it will crack the stand slot.

If you set the support spacing to 2mm it can eliminate filling the hook's v-tab with support material and promote a quick cleanup and easy assembly.

Just add a small drop of super glue to the mating surface of the hook, slide it down into the slot at the top of the stand and assembly is complete.
Try one in Glow in the dark for your nightstand!

Print Settings

Printer brand:

Printer:

Prusa Mk2

Resolution:

.2

Infill:

14%